Category: Home Improvement

0

Noisy Roof? Keep it Quiet With These Tips

If you’ve noticed a bit of odd noise coming from your roof here and there, it’s time for a quick roof repair. In Cy Fair, this project can either be handled on your own or with the help of one of the best roofing companies in the area. Either way, dealing with this problem is likely to make your life quite a bit quieter.

Before you can begin this project, there are several materials you’ll need. Make certain you get some hidden gutter fasteners. You’ll also need to get a caulking gun, as well as some caulk for outdoor repairs, a hammer, and an air gun would be fairly helpful, as would nails for your gutter fasteners. Almost any local hardware store should carry all of these items.

The first thing you need to do is figure out where you have problem areas. See if you can find any gaps in the roofing or any metal flashing that seems to be loose. You may want to use an air gun during that task to help out a bit. From there, it’s best to loosen up the gutter nails a little. That may help you spot any additional problem areas you didn’t see before. You can then go ahead and caulk any gaps you see now. Make certain you add some between the upper flashings, as well as the lower ones, to make certain you have an air tight seal.

Your next step is to go ahead and resecure your gutters, but you’ll want to do it a bit better this time. Get some hanger fasteners to help give them a little extra security. Be sure to position them about seven inches apart. They’ll need to be nailed in place, too, for added support.

To keep your roof quieter, you’ll also want to do a little more caulking as well. Add some caulk to any bit of flashing that remains loose around the roof as a whole. Let it dry for the time specified on the package, then grab an air gun. It will help you test your repair.

If these quick fixes don’t seem to do the job, you do have other options, but the best choice you have is to talk to professionals roofers. Woodlands, TXhas many different companies that can help, so your best next step is to call and schedule a professional evaluation. Roofing crews deal with this kind of problem on a day to day basis, so they’ll be able to take a quick look, decide exactly what is causing your problem, then look at the kinds of repairs that are necessary to make your roof a little quieter.

Noisy roofs are certainly an annoying problem. You can either choose to listen to the noise day after day, or take the necessary steps to repair the problem. In most cases, you’re not going to need an entirely new roof. A few short fixes should be able to keep your roof a little quieter in the coming days.

Affordable Houston Roofing Solutions
5100 Westheimer # 200-A1
Houston, Texas 77056
Phone: (832) 730-2500

Leave Your Comments »

0

DIY Windows and Doors: How to Install New French Doors

Wouldn’t it be nice to have an outdoor sanctuary; a wrap-around porch or a small and intimate patio? Imagine looking out to the bright September sun, grabbing a mug of coffee or a glass of iced tea and walking straight out to that peaceful retreat. That is exactly the type of romantic feel French doors can bring to your home. They are, of course, paired doors that open away from each other, exposing a large opening, which allows ample fresh air into the space and also entices all to the outdoors. Generally, these doors are filled with a large panel of glass or several smaller ones, so they allow a great deal of sunlight in. If you can imagine French doors tucked neatly between two of your home windows , then you will definitely want to know more about their installation.

While replacing an ordinary door can be quite simple, especially when the old and new are cut to the same dimensions, French doors can be a little trickier to install.

Interior French Doors While most people imagine the glass-fronted exterior doors when the term ‘French door’ is spoken, there are solid, interior versions which will require the existing frame to be removed with a pry bar and hammer. The opening must be checked to ensure it is square and the new frame can be set in place. It is likely that some shimming may be necessary to get the proper fit before securing the frame in place. The doors should easily mount to the framing and the job is done.

Exterior French Doors Commonly used as a secondary exit from the home, French doors are frequently used as access to a deck, patio, porch, balcony, or pool. They provide a different look than a typical door and give the feeling of bringing the outdoors in. Installing them, however, is a job best handled by Plugerville, Texas, window replacement companies, as it can be quite involved. If you do decide to go it alone, you will follow the same steps as above to replace existing doors. If this is a first time install, the whole must be cut in the wall and the opening must be framed to support the new doors. Once the new doors are in place, it is important that all seams are sealed. As with new windows, French doors improperly installed can cause bad drafts and can, ultimately, push energy bills higher. However, if they are hung with care, the doors can improve the eye appeal of your home and keep your costs at a minimum.

It is important to understand that installing French doors, particularly those leading to the outside of the home, is not a job for a DIY beginner. This is a project that should, at least, be supervised by an experienced renovator. The best solution is to hire the professionals to handle the installation, so you can be sure that the work will be good, solid, and guaranteed. Then, you will have to freedom to enjoy your outdoor sanctuary without the stress of the job.

Leave Your Comments »

0

The Steps to Properly Installing Flashing

Whenever a roof is replaced or an addition is built onto a home, there is the need for flashing. Flashing is defined as ‘strip metal used to prevent water penetration at a roof junction.’ When not properly installed, however, flashing will accomplish nothing and water can be allowed to eat away at the wooden structure beneath.

Furthermore, improper use of flashing can be a very costly mistake. If you do not feel confident in your ability to manage the project yourself, there are plenty of Garland roofing companies that are willing to take on the job. It can be worth the extra expense up front to prevent the need for very expensive Plano roof repair down the road. If, though, you are confident in your abilities, then the following guidelines can help to ensure that you perform this part of the roofing process correctly.

Measuring You will need an accurate tape measure for this step of the process and you might also want a friend who is willing to climb the peaked surface with you to ensure the proper measurement. Of course, before making any cut, you will want to know exactly what is need to cover the intended seam. It is very wise when buying the flashing material – whether it is aluminum, copper, or some other galvanized metal – that you overestimate your needs. In this way, you are covered should you make an accidental cut.

Preparation The surface that you lay flashing on should be devoid of water damage, buckling, cracking, or warping. The metal will only be an effective water barrier if it lies flat against the surface. Even the smallest gap could allow entry for water, which will undo the advantages of finding affordable Dallas roofing. Flashing should be laid before any other roofing material. Thus, before you lay the flashing, you will want to remove all roofing materials down to the planking. Similarly, if the flashing is being laid against an outer wall of the home, you will have to remove siding in that area.

Cutting It is essential, in this step, to act carefully. A wrong cut can be costly in both the time- and financial sense. Be sure that you are snipping at the appropriate length and make necessary bends at the middle of the sheet metal. If the flashing is being laid to join two roofs, be sure that it is exactly centered over the seam.

Stapling This will require a heavy duty staple gun. Be sure to hold the flashing securely in place while placing the staples. Staples should fall one inch from the out edges of the flashing, on both sides. Once the metal is securely in place and not likely to fall loose, it is possible to start laying shingles (and replacing siding).

If you follow these steps, you should have a great deal of success in your Garland, Texas, roofing project. However, if you find that the challenge is too great, it is wise to consider hiring the pros to handle it for you. The outcome will likely be far more favorable.

Leave Your Comments »